shadow

Home  >  Products & Services  >  Security  >  Expansion Modules > Elk Modules

Elk Expansion Modules

Lifesafety Power Supplies
Take your home or office security system to the next level with an expansion module from ELK Products. These modules come in several different varieties and allow you to customize your security system to provide the features that you need. The modules are ideal for security systems for homes or offices and can be installed anywhere in the Salt Lake City or Park City area. Contact Security Integrators today to learn more about these exciting products.


ELK-M1DBH : M1 Data Bus Hub (RJ45)

ELK-M1DBH
For easy connection of expanders & keypads. The M1DBH accepts up to 9, RJ45 equipped CAT5 or CAT6 cables, and series connects the data A & B lines so the data bus may be terminated properly. Two or more units may be interconnected if more than 9 data lines are required ... (more)


ELK-M1DBHR : M1 Data Bus Hub For Retrofit

ELK-M1KPB Keypad
An "active" RS-485 data bus hub designed for jobs where an M1Gold or M1EZ8 Control is retrofitting an older panel that has multiple homerun 4 conductor keypad/data wires. It splits the main 485 data bus into 4 managed 485 branches. Each branch can have 2 parallel home run cables for a total of 8 home runs. The end of each cable is EOL terminated to insure proper operation and supervision ... (more)


ELK-M1XRFTW : M1 Two-Way Wireless Transceiver

ELK-M1XRFTW Expansion Modules
The M1XRFTW two-way wireless transceiver allows an ELK-M1 or ELK-M1EZ8 control to accept Elk’s complete line of two-way wireless sensors ... (more)


ELK-M1XIN : M1 16 Zone Input Expander

ELK-M1XIN Expansion Module
Adds 16 hardwired zones (EOL resistor supervised) to the M1 Gold or M1EZ8 Controls. Operates from 4-wire data bus. Up to 12 of these can be used, increasing total zones (inputs) to 208 ... ... (more)


ELK-P212S : Remote Power Supply

ELK-P212S
The ELK-P212S is a Supervised Remote Power Supply / Battery Charger, providing 12 VDC output with up to 2 Amps of total current. It supervises the AC Power Input as well as the rechargeable Battery, and can report abnormal conditions back to an ELKM1 Control over the RS485 four (4) wire data bus. It also features relay outputs for AC and Low Battery to allow "stand-alone" operation with other Controls (Security, Access, CCTV products, etc.). Power from the P212S can be used to increase the capacity of a control, or to remotely power devices such as motion detectors, keypads, zone expanders, sirens, annunciators, etc. ... (more)


ELK-M1XRF2H : Wireless Receiver for Honeywell Xmtrs

ELK-M1XRF2H
The ELK-M1XRF2H is a Wireless (RF) Receiver and Input Expander for use with the ELK-M1 and ELK-M1EZ8 Controls. This receiver is compatible with Honeywell (Ademco) 5800 series wireless transmitters. The M1XRF2H connects to the four (4) wire data (keypad) bus of the control and integrates in much the same way as a M1XIN hardware zone expander except that a single M1XRF2H can handle up to 144 wireless zones (e.g. transmitter sensors or points) ... (more)


ELK-M1XRFEG : Wireless Receiver for GE Transmitters

ELK-M1XRF2H
The ELK-M1XRFEG is a Wireless (RF) Receiver and Input Expander for use with the ELK-M1 and ELK-M1EZ8 Controls. The receiver connects to the four (4) wire data (keypad) bus of the control and integrates in much the same way as a M1XIN hardware zone expander except that a single M1XRF can handle up to 144 wireless zones (e.g. transmitter sensors or points) ... (more)


ELK-M1RB : M1 Relay Board

ELK-M1RB
May be plugged directly into an M1G, M1EZ8, M1XOV, or M1XOVR to convert the voltage outputs into SPDT relays rated for 7A @ 30 VDC, 10A @ 125 VAC ... (more)


ELK-M1XOVR : 16 Output Expander, 8 Voltage & 8 Relays

ELK-M1XOVR
Adds 16 outputs (8 voltage, 8 relays) to M1 Gold or M1EZ8 Controls. Voltages can be used to trigger low current devices (50 mA max. each). Relays are SPDT rated for 7A @ 30 VDC, 10A @ 125 VAC. Operates from 4-wire data bus. Up to 12 output expanders may be used for a total of 208 outputs. Option: Convert 8 voltage outputs to relays using M1RB Relay Board ... (more)


ELK-M1KAM : Single Door Access Module

ELK-M1KAM
A single door access interface module for use on the M1 and M1EZ8 Control Panels. The M1KAM connects to the 4 wire keypad data bus in place of a traditional M1 Keypad. Since the maximum number of keypads on an M1 or M1EZ8 is 16, the maximum number of M1KAM modules (and controlled doors) is 16, minus any installed keypads. Even though an M1 Keypad can accept a 26 bit access reader, the M1KAM is a more powerful and less expensive access solution ... (more)


ELK-M1TWA : Amplified Two Way Listen In Interface

ELK-M1TWA
Provides 3 zones of amplified speaker outputs with adjustable volume, along with 3 zones of microphone inputs. The M1TWA can be used to add two way listen-in to the M1 Control or to just add amplified speakers at keypads and other locations in a building. Each of the 3 amplified speaker zones can drive a maximum combined impedance range of ~4 to 32 Ohms, permitting multiple speakers to be connected. Each zone includes a mute option that is triggered via an output from the control. The 3 microphone zones can handle up to 4 individual microphones each ... (more)


ELK-M1XSP : Serial Port Expander

ELK-M1XSP
The ELK-M1XSP is a "3 in 1" product for additional serial ports and for integration with lighting systems and thermostats. Jumpers on the M1XSP select the appropriate application, connection, and protocol. Best of all, the M1XSP operates from the 4-wire (RS-485) M1 Keypad data bus, allowing RS-232 ports to be located long distances from the control. The M1 Gold and M1EZ8 support up to 7 M1XSPs. The communications baud rate is adjustable from 300 to 38,400 baud. The unit comes complete with cable and a black surface mountable housing ... (more)


ELK-M1XEP : M1 Ethernet Interface

ELK-M1XSLZW
The ELK-M1XEP is an Ethernet Device Server with a RS-232 Serial Port Interface. It may be used to connect a Control in the M1 Family to an Ethernet network using TCP-IP protocol for programming, remote control and monitoring. It features a secure embedded web server, with a user interface built on a Java applet, and email event notification. A software setup utility is built into ElkRP (version 1.5.0 or later) for configuring the connection setup, network password, etc. The M1XEP is factory defaulted to obtain a dynamic IP address from a DHCP server (i.e. Ethernet switch, cable modem, etc.), however it may also be setup with a static IP address ... (more)


ELK-M1XSLZW : M1 to Leviton Z-Wave Interface

ELK-M1XSLZW
The M1XSLZW is a specialized Elk-M1 serial expander for connecting an M1 Control to Z-Wave enabled devices through a Leviton VRC0P+3 Z-Wave Serial Interface. Z-Wave is a wireless, low power, "mesh" network technology widely used for automating devices such as: Lights, Thermostats, Electronic Locks, etc. Z-Wave empowers devices to be remotely controlled from across the room or across the world with benefits such as energy savings, convenience, and comfort ... (more)


ELK-M1XSLU : M1 to Lutron RadioRA2 Interface

ELK-M1KPB Keypad
The ELK-M1XSLU is a dedicated Elk-M1 serial expander for connecting an M1 Control to a Lutron RadioRA2 Main Repeater. RadioRA2 is a wireless multi-room control system for Lights, Shades, and HVAC Thermostats. Interfacing a RadioRA2 system to an M1 allows control in response to security system actions or conditions. With the automation and remote capabilities built into M1 it is possible to control RadioRA2 devices from across the room or across the world. Benefits include energy savings, convenience, and comfort ... (more)




bottom